--- a/zlib/uncompr.c	Sun Aug 21 07:07:55 2011 +0900
+++ b/zlib/uncompr.c	Fri Oct 27 22:46:09 2017 +0900
@@ -1,5 +1,5 @@
 /* uncompr.c -- decompress a memory buffer
- * Copyright (C) 1995-2003 Jean-loup Gailly.
+ * Copyright (C) 1995-2003, 2010, 2014, 2016 Jean-loup Gailly, Mark Adler
  * For conditions of distribution and use, see copyright notice in zlib.h
  */
 
@@ -9,53 +9,85 @@
 #include "zlib.h"
 
 /* ===========================================================================
-     Decompresses the source buffer into the destination buffer.  sourceLen is
-   the byte length of the source buffer. Upon entry, destLen is the total
-   size of the destination buffer, which must be large enough to hold the
-   entire uncompressed data. (The size of the uncompressed data must have
-   been saved previously by the compressor and transmitted to the decompressor
-   by some mechanism outside the scope of this compression library.)
-   Upon exit, destLen is the actual size of the compressed buffer.
-     This function can be used to decompress a whole file at once if the
-   input file is mmap'ed.
+     Decompresses the source buffer into the destination buffer.  *sourceLen is
+   the byte length of the source buffer. Upon entry, *destLen is the total size
+   of the destination buffer, which must be large enough to hold the entire
+   uncompressed data. (The size of the uncompressed data must have been saved
+   previously by the compressor and transmitted to the decompressor by some
+   mechanism outside the scope of this compression library.) Upon exit,
+   *destLen is the size of the decompressed data and *sourceLen is the number
+   of source bytes consumed. Upon return, source + *sourceLen points to the
+   first unused input byte.
+
+     uncompress returns Z_OK if success, Z_MEM_ERROR if there was not enough
+   memory, Z_BUF_ERROR if there was not enough room in the output buffer, or
+   Z_DATA_ERROR if the input data was corrupted, including if the input data is
+   an incomplete zlib stream.
+*/
+int ZEXPORT uncompress2 (dest, destLen, source, sourceLen)
+    Bytef *dest;
+    uLongf *destLen;
+    const Bytef *source;
+    uLong *sourceLen;
+{
+    z_stream stream;
+    int err;
+    const uInt max = (uInt)-1;
+    uLong len, left;
+    Byte buf[1];    /* for detection of incomplete stream when *destLen == 0 */
+
+    len = *sourceLen;
+    if (*destLen) {
+        left = *destLen;
+        *destLen = 0;
+    }
+    else {
+        left = 1;
+        dest = buf;
+    }
 
-     uncompress returns Z_OK if success, Z_MEM_ERROR if there was not
-   enough memory, Z_BUF_ERROR if there was not enough room in the output
-   buffer, or Z_DATA_ERROR if the input data was corrupted.
-*/
+    stream.next_in = (z_const Bytef *)source;
+    stream.avail_in = 0;
+    stream.zalloc = (alloc_func)0;
+    stream.zfree = (free_func)0;
+    stream.opaque = (voidpf)0;
+
+    err = inflateInit(&stream);
+    if (err != Z_OK) return err;
+
+    stream.next_out = dest;
+    stream.avail_out = 0;
+
+    do {
+        if (stream.avail_out == 0) {
+            stream.avail_out = left > (uLong)max ? max : (uInt)left;
+            left -= stream.avail_out;
+        }
+        if (stream.avail_in == 0) {
+            stream.avail_in = len > (uLong)max ? max : (uInt)len;
+            len -= stream.avail_in;
+        }
+        err = inflate(&stream, Z_NO_FLUSH);
+    } while (err == Z_OK);
+
+    *sourceLen -= len + stream.avail_in;
+    if (dest != buf)
+        *destLen = stream.total_out;
+    else if (stream.total_out && err == Z_BUF_ERROR)
+        left = 1;
+
+    inflateEnd(&stream);
+    return err == Z_STREAM_END ? Z_OK :
+           err == Z_NEED_DICT ? Z_DATA_ERROR  :
+           err == Z_BUF_ERROR && left + stream.avail_out ? Z_DATA_ERROR :
+           err;
+}
+
 int ZEXPORT uncompress (dest, destLen, source, sourceLen)
     Bytef *dest;
     uLongf *destLen;
     const Bytef *source;
     uLong sourceLen;
 {
-    z_stream stream;
-    int err;
-
-    stream.next_in = (Bytef*)source;
-    stream.avail_in = (uInt)sourceLen;
-    /* Check for source > 64K on 16-bit machine: */
-    if ((uLong)stream.avail_in != sourceLen) return Z_BUF_ERROR;
-
-    stream.next_out = dest;
-    stream.avail_out = (uInt)*destLen;
-    if ((uLong)stream.avail_out != *destLen) return Z_BUF_ERROR;
-
-    stream.zalloc = (alloc_func)0;
-    stream.zfree = (free_func)0;
-
-    err = inflateInit(&stream);
-    if (err != Z_OK) return err;
-
-    err = inflate(&stream, Z_FINISH);
-    if (err != Z_STREAM_END) {
-        inflateEnd(&stream);
-        if (err == Z_NEED_DICT || (err == Z_BUF_ERROR && stream.avail_in == 0))
-            return Z_DATA_ERROR;
-        return err;
-    }
-    *destLen = stream.total_out;
-
-    err = inflateEnd(&stream);
-    return err;
+    return uncompress2(dest, destLen, source, &sourceLen);
 }